logo

Info

Reviewbucket.co.uk scanned the internet for NZXT Kraken X63 reviews.
You can find all NZXT Kraken X63 reviews and ratings on this page.

Read the reviews.

Analysis

For NZXT Kraken X63, 207 customer reviews collected from 1 e-commerce sites, and the average score is 4.

Detailed seller stats;
Amazon has 207 customer reviews and the average score is 4. Go to this seller.

Detail

Click to list all products in this category.

Similar Items

7.1.2019

For my first ever PC build I wanted an AIO Liquid Cooler that looked great but also performed with minimal noise. Having bought the NZXT S340 Elite Case I wanted to match it with similar hardware - mainly for astherics reasons. I was originally looking in the market for a standard air cooler but since I've purchased the i5 8600k and planned to overclock it, I knew I needed something better to keep the temps down as well as the noise. I can assure you this exceeded my expectations. My CPU temps at idle hovers around 25c-30c and when playing games it never exceeded 60c after playing for a couple of hours. Using the CAM software I applied my own custom profile and never looked back.There are about 4 presets available for the pump and fan. But I wanted full control on the temps so decided to apply my own custom profile which personally for me was a better option but the presets are good enough if your not planning to overclock especially at 5ghz. With all that being said, I did come across one or two problems. One of which involves the screws or thumb screws that locks the cooler block to the motherboard in place. The screws themselves weren't the problem its mainly the fact that they all (almost) look identical from one another. This could be just me, but trying to find the correct one was a struggle. It took me over an hour to realise I've been trying to put the wrong screws in. Eventually, when I found the correct one it was a breath of fresh air as it was a simple installation from then on. Now for the other problem, it doesn't necessarily involve the hardware itself but the software. The CAM Software is a love and hate relationship. When it works it's amazing, but when it doesn't your left with a white light and the ring is stuck on a constant loop. In worst situations, it doesn't even detect the Kraken X62!! Which means you can't even do any sort of customisation with the lights, fan/pump profile or even see the temps. As far as I know, there aren't any real solutions other than restarting or reinstalling the software or restarting your PC. In most cases this fixes the issue but sometimes you have to restart multiple times for it to detect it if your lucky. Although this doesn't happen often however it can be frustrating having to restart or reinstall the software when it does. NZXT really needs to fix their buggy software. But don't let this out you off, even though it can be annoying when it works it's great. The amount of customisations available with the lights etc are one of the best I've seen. That's if your into RGB which you should be if your thinking of getting this cooler as its one of its selling point. Overall, the Kraken X62 has a great high quality design combined with various customisations that are subjective cause some of the lighting modes I don't use but that's just me. I like to have a minimilistic setup so I only use one or two modes that are applicable to me but the other modes are great also. The only thing that's letting it down really is the software as it can be buggy at times. But other than that, this is a fantastic cooler. Highly recommend for anyone who loves RGB and customisations and a cooler that operates quietly while keeping CPU temps at a minimum.PS. The software is the only thing that's stopping me from giving this otherwise great Cooler a 5/5 stars.
Read more..

5.6.2020

I know this product has been discontinued however if you are like me and do not want to use CAM software this should still work on all NZXT AIO coolers.Instead of connecting the fan cables to the supplied wiring harness that goes to the pump get a PWM splitter cable then plug the water pump and 1 of the fans into the splitter then the splitter into the CPU_FAN header on the motherboard, the other fan can be plugged into the CPU_OPT header (CPU_OPT takes the temp from the CPU socket there for 1 fan will run slightly slower but it will gave better performance/cooling). If your only using 1 fan simply plug the fan and the water pump into the splitter then the splitter into CPU_FAN header.You will need to create/change fan profile in the BIOS as I have found 1 issue with the water pump,when it reaches above 2100rpm there is a vibration from the motor that resonates through the case.These are the setting I used on a ASUS Sabertooth 990FX R2 to keep it quite without vibrating and overheating you may need to change yours as results can vary.CPU lower temp set to lowest, CPU highest temp set to 75c (this gives the fan and pump more rpm range as the temp raises, CPU low fan speed set to lowest and CPU max fan speed 96% this will stop the pump going over 2100rpm.The AIO cooler is relatively simple to install if you are attaching the radiator directly to the case and the fans underneath it.However it isn't very well designed if you want the fans in-between the case and the radiator, it does support it as it states this in the instructions and you will need someone to help you as it is awkward as you have to rest the fans on the radiator making sure the holes line up then line the holes up on the case.It comes with a lot of fixings for both AMD and Intel including AMD Ryzen AM4 and Threadripper TR4. I found that it is designed for the stock AM3+ CPU mount which means there is a risk you will end up damaging the motherboard as you put pressure on to the clip. NZXT should have made their own back bracket.If your using any monitoring software other than CAM you will notice there is a CPU fan speed that is the water pump speed, you can also see this in the BIOS.There are alot of reviewers stating they can hear trapped air in the system, mine also had this problem but seems to of sorted itself after a few burn in tests with Prime95, Cinebench r20 and FurMark CPU burn.I am currently running a AMD FX 8350 overclocked from 4Ghz to 4.8Ghz @ 1.44v with a max temp of 80c on the cores when stressed and 65c gaming.Overall I am very happy with this purchase.
Read more..

21.12.2019

So you'll see I gave this 5 out of 5 - that is a score purely for the performance. Quite simply it's the best AIO around. You can't beat the performance this thing gives. I get 5GHz OC on 9600K idling at barely 30C and under non AVX Prime 95 it's 70C. AVX is unecessary - no point proving your car can carry a jumbo jet 24/7.So for the pure performance it's superb. And that's what I bought it for. That and the noise levels.Ok, here's where it gets more complex. The fans aren't the quietest around - they give 2000RPM at full blast and they sure tell you about it. 3x120MM (x72 version) and they're not built for absolute silence,not at that pace.But you will really realistically never need the fans much higher than about 40% which is barely 900RPM and while still audible it's way quieter.However, the flaws should be highlighted now:CAM is a mixed batch - it's a decent enough app but the hardware should NOT have to rely on software to function. That this kit doesn't function at all outside windows is an appalling oversight and unnacceptable at this price range. So pure silence in idle, yes, but switch user or reboot - WOOOOOSSH as the fans go back on and the user switch process gets black screened for 20 seconds. Software is bad and that MUST be emphasised. The talking back to the mothership stuff I'm not happy with either, but I don't care as much about it as some.Secondly the install is hard - the Kraken lives up to its name with a stupid number of cables - while the basic kit looks lovely, the cabling is hideous and you MUST hook this up to SATA power or it does not work. At all. The design here is just horrible horrible horrible.HOWEVER - I have bypassed a number of these issues with some mods - I have hooked all fans up to the mobo and am using Argus Monitor (£10) to control the fans - CAM is now gone and the unit works as it should without. There is no black screen delay any more and the fans don't go ballistic outside windows now. But a lot of users might not suss to do that.I would also say the included fans just aren't quiet enough at full blast - they're built clearly for performance not total silence and you're better off replacing them with alternative 4-pin PWM fans.HOWEVER:For the basic purpose of performance and overclocking and idle silence, the Kraken is pretty much the best there is. It has some crippling design issues and they're nearly deal breakers if you can't figure out bypasses, but if you can you have the best and most efficient kit around.Just be prepared to work at it.
Read more..

31.5.2020

My first foray in to water cooling. The best configuration for my case was a 280mm radiator and I was going for a quite 'colourful' build so I decided on this as it had got good, solid reviews.Fairly easy to fit for a first-timer with the most fiddly bit being that the pipes are quite stiff to move about.The fans can be quite loud when spun right up and the pump itself also generates a bit of electronic-type noise, so it's advisable to play around with the fan and pump profile using the CAM software to only have everything really spin up when required. I have custom profiles set up so that everything is almost silent for general use but when gaming the pump goes up to max and the fans around 60-70%.It's still not that noisy like that and the fans only go up to 100% when the CPU hits 80 which tends to only be when running bench-marking or stress testing.The water block/pump looks the business with the pulsating circular lighting and this can be customised using the CAM software too.There has been a lot of negativity regarding CAM but this generally seems OK now. If you have other software that interact with your hardware, like Gigabyte Aorus or Corsair Link, then this can interfere with the CAM software meaning the CAM loses control and hence your fan curves go out of the window. So, if you have everything configured for silence and you start machine and it sounds like a jet engine, check CAM and it will tell you if another piece of software has 'control' rather than it. Unfortunately, it won't tell you which piece of software is the offender so you'll need to play around killing processes etc. and restarting CAM.Overall pretty happy with it. It does a decent job of cooling (although I would say it's not as responsive as an air cooler) and looks the business - a much cleaner look than an air cooler. It's not as silent as you might think but then it still has two fans to spin up and the pump itself can be heard when on full pelt. The CAM software, however, does now seem stable and if you do run in to any problems, check what else you're running first.
Read more..

21.9.2018

It now works efficiently, but I had to change the way its fan operated, so it pushed the air over the rad and out, not pull the air through. My cpu overheated with the latter setup. And I added some extra thermal paste which may have helped.I love the graphics coming from the pump head, lots of different designs and colours you can custom setup. The cpu holder was easy to yake off, but the NZXT holder was difficult to install (my case aperture was no wide enough so had to hold plate in place whilst threading bolts through by touch, but once in and attached it holds the pump securely.The rad and fan stand proud of the case inside and because my two side fan apertures are close to the end it wasreally fiddly to get both 120mm in place and it needed two to inject enough cool air to allow the rad fan to cool the rad. in the end I had to use a 100mm fan instead though the side panel is not fully on at the top because of the tight fit.Thats just a case design gremlin so not their fault, just bear that in mind.EDIT: Not sure why but without changing anything am now getting temp warnings again and it's not that hot in the room. I was hoping this had solved my problems but I think I need to research other makers as this is crazy might even go back to an air rads now.EDIT#2. So feel a bit stupid but stupid me had applied too much CPU heat paste. I cleaned all of it off and reapplied a small amount, just a 5mm blob, tighten the bolts by hand not using a srewdriver just enough to hold it firm. Major change of case leater and fan is now mounted in roof of case.Result, no overheating problems and even in the summer too.I have changed score to 4 stars as the Logo is not changeable, its upside down due to I/O tubing being too close to RAM cards so had to route it opposite side round.
Read more..

25.2.2020

To get straight to the point, if the kraken has too much air in the pump when you switch on the system, your CPU will overheat. Let me elaborate.The Kraken is a closed loop liquid cooler, and you cannot let air in or bleed it out. THAT BEING SAID there is always a small amount of air inside, and if the air bubbles all congregate inside the pump housing it can heavily impede water flow, and your CPU will reach boiling point- not helpful when it relies on water to cool it!The instructions do not warn you of this or provide any instructions to avoid it, so here’s mine-Lay the radiator on top of your PC for several minutes after attaching the pump to the CPU bracket.The air will move up to the radiator and away from the pump, ensuring the CPU is safely cooled during your first boot.Please screenshot this if you have decided to buy, it may just end up saving your CPU.Besides that the kraken x62 and x72 AIO coolers have served me perfectly well across 3 systems, and the CAM software is now hugely improved since the 2018 era. The 2 flexible tubes are long enough for even the biggest cases while still fitting well in more compact builds.At this time the only reason to look elsewhere is purely based on aesthetics.
Read more..

15.9.2017

●Run downPros:°Exlant software°Easy installation°Best looking CPU all in one (in my eyes)°Fantastic build quality°Keeps your gear frosty (cold)Cons:°The x52 produces the same cooling outcome as it's big brother the x62 (Get the x52 it's just as good)°Fan edges are a little week when screwing in.°The temps in software dose not refresh very fast°Incresing pump speed dose not do much●In-depth run downThis is an excellent little cooler kept my i7 700 very at good temps, it has easy installation and looks fabulous yes fabulous the CAM software that comes with the cooler is very in detail and has a lot of options and graphs for diagnosis of temperatures and speeds the only problem is the temp refreshrate of the gage seems a little slow and jumps from say 20 to 40 then back down randomly.● BIG HEADS UP ●I purchesd the x62 and the x52 and I have some things to say about them both. So I tried the x62 for about a week and then swaped over to the x52 and I have to say the temps did not change much AT ALL at idle for 30min they stood about 1c of each other and at 100 load they where exactly the same. So much so that I returned the x62 to get it's little brother to save space for an extra fan.
Read more..

11.11.2018

I have bought this product to replace my Noctua NH-D14. The case that I have used for this is a BitFenix Prodigy M, and that has a 240mm slot above for the radiator to fit, and mine fits in perfectly! (along with some adjustments)It's fantastic how you are able to rotate the L-shaped tubing on the pump, as it definitely helps on adjusting the tubes so that it has less stress, and so that there's no visual intrusion on my RGB components.The Infinity Glass implementation is superb, and I cannot recommend this design any more that what I can describe. You simply have to see it for yourself.It is quite a dear cooler for its performance. My Noctua NH-D14 was purchased for half the price and it performs a little bit better than this cooler,although this cooler is still not considered "awful" - this is definitely a fantastic contender against the other coolers like the Corsair H100i.It's definitely recommended for you to purchase this cooler if you are like me, who want RGB lighting in your PC, want to achieve high overclocks, yet keep it all in a small form factor (mATX in my case). Of course it's not exclusive for people on that list, but it certainly will tick the boxes for you if you are!
Read more..

25.6.2020

NZXT KRAKEN Z73 360mm AIO WATER COOLERPROS:- Stunningly Crisp Colorful & Sharp HQ Graphical LCD Display on the Pump- NZXT Software is Solid, Responsive & a Breeze To Use- Up-Loading GIFs to the Pump LCD Screen is Ridiculously Easy- Pump is Quiet in Full Mode- The Stock Fans are also pretty quiet in full mode too- Cools my Very HOT AMD Ryzen 3900x CPU like a Pro- 70c idle with Ryzen Wraith Stock Cooler & 43c idle with the Kraken Z73 on an Extremely Hot Summers Day !!!- Flexible Pipes make it easy to install- Looks GorgeousCONS:- Absolutely NoneMy Current PC Specs are:- AMD Ryzen 3900X- NZXT KRAKEN Z73 360mm 3 Fan AIO CPU WATER COOLER- NVIDIA EVGA GeForce RTX 2080 Ti FTW3 ULTRA GAMING 11GB- ASUSX470 ROG Crosshair Hero VII Socket AM4 Motherboard- 32GB Corsair Vengeance RGB PRO DDR4 Ram 2x16GB 3600MHz CL16 Kit- Corsair RM850x 80 PLUS Gold, 850w PSU- Fractal Design Define R6 EATX Case- Three LG 24in MonitorsGod i Love This Cooler LOL ?This is my very first NZXT Purchase so i thought id go BiG ... i'm glad i did :)I think this product makes all other AIO Coolers look boring ... iMOI Recommend This Cooler & I Hope This Review Helps ?
Read more..

10.5.2019

I had a Corsair H100 before but the bearings went, i moved over to air CPU cooler and that couldn't handle and mediocre OC i had so i thought sod it Get the Kraken X62 and hope the fixes it, And oh boy it doesn't disappoint. It's expensive but now i can game again no problem, temperatures are decent, It's very quiet, looks wonderful and so far so good. I did read some units had problems i hope i got a good one (not too worried though as it has a 6-year warranty!)... But if there are problems i will be back to amend my review.. If there's no amendments it's a goodun! 5 out of 5 rating.EDIT: The software side has some niggles...Having to online login before the CAM fan controller software starts,seems a very silly way to do things unless i'm missing something. Fan profiles should kick in THEN login. Also having a BIG BLUE delete (profile) button right under the presets list.. seems a bit silly placement. Accidentally delete the preset i want to switch to many times. I hope they can address these easily fixable things. Still a great cooler though i won't alter my mark.
Read more..

6.10.2018

Well built and easy to install using the included AM4 bracket. There is just enough room at the top of my Obsidian 450D case to accommodate the 280mm radiator and fans. I didn’t use the supplied NZXT fans, instead I installed Corsair 140’s in a pull configuration as I wanted to maintain the RGB theme but the supplied 140mm fans appear to be good quality and will find a home on a different project. The Kraken keeps my Ryzen 2700X around ten degrees cooler during benchmark runs and easily out performs the dual fan tower cooler it replaced. The pump is super quiet and completely inaudible with the case closed up.It has some nice RGB features on the CPU block and customisable fan profiles however the CAM application required to set this up is a bit hit and miss for accuracy as well as eating system resources when running. The block is supplied with thermal paste pre applied but I removed this before installation and used my trusted Thermal Grizzly Kryonaut so I can’t comment on how effective it is.
Read more..

6.1.2019

Let me start by saying I absolutely do not NEED this cooler. I have an i5-4460 so an AIO is completely overkill for me.However, the design sold this to me. The lighting effects which can be configured within NZXT's CAM software are nothing less than amazing. This product has completely transformed the look of my system.On idle, with the fans running about 20% speed, I average around 28-30 degrees Celsius after around an hour running. In intensive tasks, temps never increase by more than 5/10 degrees.One thing I was uncertain about before I purchased this product: the noise. I don't have an overly powerful rig so being silent is quite important for me. Nevertheless,the NZXT fans are surprisingly quiet and have lowered the amplitude of my system overall.Very pleased with this cooler.
Read more..

26.7.2019

Beautiful looking radiator and stylish pump. NZXT paid attention to detail with this.The box comes with instructions but I've found it easier to look it up on youtube and they can be slightly confusing to newcomers.The fans are smooth and quiet even under full load with headphones on I cannot hear it and people down the mic cannot hear it also.The pump doesn't make any audible sound it is the fans that make a humming sound.The pump has a nice infinity loop going on and yes you can control the speed and color using NZXT CAMunfortunately, you cannot use Aura yet.The pump requires 3 cables, 1 to an onboard USB socket,1 connects to the fans and another to the power.This a beautiful looking pump and radiator and I recommend to anyone that has an NZXT case since it fits perfectly.
Read more..

16.4.2019

Well I wasn't looking forward to replacing my liquid cooler but I have to say it went in very easily. The radiator is thinner than my previous one (Enermax) and that alone makes it easier. Even the heat conducting paste is pre-applied so no problems with that either. And once fitted, the cooling seems more effective than the Enermax too, even though the plate is a little smaller than the die on my CPU (Threadripper 1950). It's early days in terms of reliability, but other than that this is a very good buy. PS I've seen adverse comments on the web about problems with the NZXT-supplied control software but I'm not using that because I'm not interested in LED lighting etc.I've had no problems using the standard ASUS fan control software that came with the motherboard.
Read more..

10.1.2020

Picked up the Kraken X62 AIO Cooler for Intel's i9 9900KS processor. It's job is to regulate the CPU temperature in a newly built Video Editing PC build. The radiator was super easy to mount to the front of NZXT's H510 Elite case providing adequate airflow with the included intake fans as standard. The CPU temperatures remain at roughly room temperatures during office and web browsing, mid 40's while Editing 4K footage with Premiere Pro, Playing Battlefield V, Call of Duty MW, and 55C MAX at 100% utilisation with PRIME95. The cooler block features RGB lighting which can be controlled via NZXT's App. The cooler block and back plate is also very simple to install onto a motherboard of your choice.Absolute Kraken' piece of engineering! Would purchase again! - Jake
Read more..

List All Products

Terms and ConditionsPrivacy Policy