logo

Info


Reviewbucket.co.uk scanned the internet for Corsair H80i Hydro reviews.
You can find all Corsair H80i Hydro reviews and ratings on this page.

Read the reviews.

Analysis


For Corsair H80i Hydro, 523 customer reviews collected from 1 e-commerce sites, and the average score is 4.3.

Detailed seller stats;
Amazon has 523 customer reviews and the average score is 4.3. Go to this seller.

Detail


Click to list all products in this category.

Similar Items

27.10.2016

Having owned this for about a week now, I thought I might leave a review and give some advice to those looking at getting a AIO liquid cooler. First let me say that this is my first water-cooler that I have ever installed, so with that in mind I want to highlight the following.1. For those of you building a PC on a tight budget with not much care for aesthetics, I would go with an air cooler with a big heat-sink (e.g. Hyper Evo 212 or ARCTIC Freezer 7 Pro) because if you stick a Noctua fan on there you'll have a far quieter and probably better experience, for far less. However if you are like me and love the aesthetic that a water-cooler provides and hate big heat-sinks getting in the way of your RAM sticks and motherboard,then water-cooling is definitely the way to go.2. The noise. These fans are very noisy at anything over 50% speed, and are small vacuum cleaner level at 100%. Corsair tell you in the manual to plug both fans into the cable coming off the pump housing, and then the cable that comes off that into the cpu fan header. This didn't work for me because while running basic tasks the fans would ramp up to 100% sporadically which became very distracting. I started looking on forums and people were having similar issues. I read somewhere that the pump should stay at 100%, because this provides the best cooling and means less wear and tear on the pump (a changing load is much worse for it). To fix this I simply plugged the main cable that comes off the pump housing into the 3 pin water pump header on my motherboard (this stays at 100% all the time), and plugged in the two fans into CPU_FAN and CPU_OPT on my motherboard. Then I controlled them all using the fan controller in my UEFI BIOS to keep them both below 50% as much as possible.3. With all that being said it really does keep my processor very cool - my core i7-6700k clocked at 4.7 GHz wasn't going above 70*C and at idle it sits around 20 - 25*C depending on room temperature. I also like the RGB control of the corsair logo, which can be changed with corsair link software and configured to changed based on CPU temperature. I have mine on white most of the time and set to change to red when it goes over 70*C.All in all a very good all in one closed loop cooler, but I have to knock off a star for the fan design. While they may be high static pressure fans and work well at pushing air through the radiators, they far too noisy at anything above 50%. Those who have their hearts set on this you have two options: A) Do what I outlined above, if your motherboard allows it -enough fan headers, fan control in UEFI BIOS- or B)You can swap the fans out for some quieter 120mm fans. Noctua NF-P12 PWM fans would probably be a good option, though brown doesn't look too great in most builds.
Read more..

18.7.2020

.. a vast improvement over any 'stock' cooler or many aftermarket passive or active air coolers. Please note that I can't comment on Intel mainboards, but I've added these to a few AMD machines and they all work wonderfully.To install this on an existing machine, you may need to disconnect and remove *everything*, as the mainboard needs to be removed from the case (unless the case has a removable right/lower panel). The plastic heatsink then needs to be removed (crosshead screw) and the metal retaining plate will then come away from the rear of the mainboard.It starts to be tricky here. The radiator unit needs to be screwed to the (normally) back of the case,the CPU should be in place (clean of any previous thermal paste or pads) and secured in the ZIF socket. You'll then need another set of hands to hold the rear plate in place, plop a pea-sized blob of thermal goo on the centre of the processor and then plonk the heatsink and retaining bracket in place, then get the four (supplied) screws through the correct holes (AM3 and AM4 are slightly differently placed), ensuring that the heatsink doesn't wobble too much while you're doing it.The instruction manual is rather vague on the installation process, and if you do a YouTube search on "how to do it", the majority are all running bare machines, and don't actually show you how fiddly it can actually be!Take a look at the photo - the two white fans are 80mm - the H45 is 120mm, and needs an additional 40mm above or below for the waterpump enclosure - PLEASE check the size of your existing or new case before you go down the water-cooling route.On the upside - that machine is a Phenom II x4 955 (3.2GHz) - with the original (air) cooler it ran happily at around 45-50°, but when that failed (8 years - not bad), I replaced it with a succession of £30-40 air-coolers, and it would usually run anywhere between 60-80° - then cut out at 84°. It's an old lady now (16Gb DDR3) , but actually outperforms my Ryzen 5 3600 (48Gb DDR4) with identical graphics cards (Radeon RX570 8Gb), and it runs With this, it's running at no more than 43° under stress-test load, overclocked to 3.6GHz.If you want a very well performing cooling solution, and you're not afraid to really start pulling things to bits (and putting things together again), you can't really go wrong with this - but ensure you have enough thermal paste to hand. The chances are you *will* make a mess the first time around, but be patient.Hope this is of use!
Read more..

29.8.2019

I was fed up having my Windows machine crash with heat issues when transcoding video using Handbrake so I decided to upgrade my Noctua fan to this water cooler. Glad I did.The unit is easy to install as long as you have a basic understanding of your case and motherboard. Carefully check which risers you need for your board (Have a look in your motherboard manual if unsure on type to use).Comes with pre applied thermal paste which is great although I suggest you make sure of position over the cpu so as to avoid moving it about after fitting and smearing the paste.Under normal load the pump and fans are barely audible provided you download and configure the iCUE software from Corsair.This software allows you to set custom fan and pump performance based on heat of various sensors, I use the CPU sensor to drive the power of the fans and pump which seems to work well however you can adjust according to many other sensors too.The same software can be used to adjust the lighting on the unit although there is no lighting on the fans or radiator (Which suits me fine).Other Corsair hardware can be configured using the same software which is useful as I have a Corsair keyboard.At full load and in the height of the hot weather we have had my CPU was peaking at 63 degrees which is way lower than the temps with the fan cooler. Be warned though, the noise level is significant when the fans and pump are running full speed to keep the CPU cool in hot weather however there isn't really any way to avoid this.The only gripe I have is that the fans are set according to current user so if I am running an intensive heat generating process and someone else logs into their account on the same machine, it sets the fan according to their usage which can lead to overheating the CPU. If anyone knows a way of getting round this would love to hear - As a workaround I set the same iCUE settings in everyone's account on the same machine however would prefer if the setting could be made globally rather than on a per user setting.You will need a spare USB header on your board to use this unit and I had to disconnect one of the leads from my front of case USB units however not a big deal if you have a spare.
Read more..

30.5.2017

It's Summer, it's hot, I'm hot, and the fact I'm playing games and my CPU temp is pushing 100 degrees C makes that worse. It wouldn't help longevity either. So I decided to order the Corsair H100i V2 240mm. It arrived today, I unboxed it like a child at Christmas, and attached it to the computer as quickly as possible to give it a test. Very early impressions are excellent.The installation into my LGA1151 socket was simple, couldn't be any easier, and it all falls together nicely. I only have one real complaint about this aio system and it's the fact that the pipes are stiff. It just feels like they don't want to flex and I still don't feel comfortable with it now.Upon testing I have found a significant reduction in temperatures. Of course, coming from a stock Intel cooler, it is obvious I'll see such massive reductions.Idle temp with Intel cooler: 40-50 degrees C.Corsair Idle temp: 25-27 degrees C.light/medium load Intel cooler: stayed around the 40-50 degree mark pushing 60 on medium loads.Light/medium on Corsair H100i V2: Bouncing around 27-35 as the pump/fans continually adjust to the temps.X-Plane 11 loading on Intel cooler: 100-101 degrees C.X-Plane 11 loading Corsair H100i V2: 54 degrees C max.I only tested that because X-Plane 11 really pushes hard when it's loading the flight up. When the game has loaded the temp drops down to 35-40 degrees C on the Corsair H100i V2. On the Intel cooler it stayed at around 80 degrees C.Previously, when I had my Intel Core i7 5930K, I used a Cooler Master V8. It was just an insanely large cooler and for all of that size it doesn't match the performance of this. I got rid of it because of its size as it was pushing on my GPU and I had to take off the backplate and it was just a nightmare. Not worth it.Just as a quick side-note to monitor the CPU temp I am using the debug LED on my motherboard. It's quite accurate and is easy to see. I have the system plugged into the USB header on my mobo so I can control it via Corsair Link. I have set it all to performance mode, though I may customise it myself.Just so people are aware, I do know 100 C is extremely bad, hence my order of this product.
Read more..

6.7.2019

Bought this as I had the previous H60 version which I hoped would be a straight swap which it was.The unit was very easy to install even with the chaotic wiring in my particular computer. The hardest thing I had to do was plug in the 2 connectors for the liquid cooling and fan which were in the the most inaccessible places on the mother board, but that's not really the fault of corsair to be honest.It would have been nice if the instructions gave a little more guidance on how to locate the connectors as there are about four possible connectors to choose from on a motherboard, I thankfully had the foresight to note where the previous cooler connectors were plugged in.On boot up the inside of the computer was bathed in white light which I didn't expect but is nice anyway.However the fan does make a fair bit of noise and stays on permanently, I found this a little annoying as the packaging makes a big thing about it being really quiet, this is not help by it triggering a resonance with my side cases side panel either which means I have to give it a kick once in a while, grrr! I can't stand noise.One thing to be aware of after installing the unit is that it takes a little while for it to effectively keep the processors cool, I believe this is because the thermal paste needs time to properly seal the components together probably through heat transference, so don't be surprised by this. For me it took about 2 or 3 days of fair usage before the temperatures settled down to a normal level. It should still keep the processor cool enough to use without damage though from initial use.Overall, I'm satisfied even if the fan is louder than expected.
Read more..

29.7.2016

Really love this cooler. Installed in the top of my case (Phanteks Enthoo Primo) with the fans pulling air through the radiator, as an exhaust, so didn't expect the best results ever, but pulling air instead of pushing air makes it easier to clean any dust on the radiator fins, but to my surprise my I7 6700k still runs at a very cool 22-23 degrees idle and when stress testing under load it topped out at 62 degrees (Overclocked at 4.6GHz) so really happy with the results from the H115i.The Corsair Link software is ok, not brilliant but does the job, allowing to set fan / pump speed with some preset options and allows to set a custom fan curve if needed and change the LED colour on the cooler too.The fans supplied can get very loud if left to run high but setting a fan curve, I have the system cool with only a very low hum from the fans, which when gaming is not noticeable at all, so very happy I didn't need to replace the fans, but that is an easy option if the noise bothers someone.The only problem I had was when installing the H115i. The Intel bracket is pre-installed (AMD bracket is in the box) and the instructions say there is 1 set of screws for Intel and 1 set for AMD, but I couldn't get the Intel screws to screw down to the back plate at all. Turns out there is 3 sets of screws for some reason ? 2 sets look nearly the same but the threads are a bit smaller on 1 of the sets, so make sure you check the mounting screws fit the the thumb screws before you fit them to the back plate or you will have to remove the back plate and swap them before it will fit.
Read more..

27.6.2020

Corsair iCUE H100i PRO XT RGBExcellent quality cooler very easy am4 install just using stock board mount Intel is a little more work by the looks , am4 just two ring hooks with thumb screws just clip on and tighten up done ,, I switched out the fans for uphear rgb fans as had couple spare was cheaper than buying the rgb fan version, if like me you incounter the rgb pump not lighting up even though all connection are connected as in the manual you will find its down to the sata cable that connects to the sata link for the light for some reason it needs the 5 pin/cable prob for the 5v if like me my modular psu has 2 sets of sata leads one with all sata and one with a 4 pin molex as well as sataand I had it plugged into the one with the molex counting the cables on the lead sure enough it had 4 strands and the one with just sata had indeed got 5 strands of cable swapped them and boom the pump head lights up so something to look out for incase you have same issue also you can't use adapter extension via molex to sata as well , icute software is excellent loads of rgb light configurations and temp monitoring and fan speed profiles , all in all a very good cpu cooler running my Ryzen 7 3700X idal 24.9c , its definitely worth spending the extra £40/50 for quality over say the cheap Golden field or one that's likely to leak and ruin your system , pump is fairly quiet as well little noise but not distracting at least you know its running lol buy one you won't regret it
Read more..

10.12.2014

If you're looking at the H55 as an entry into the world of all-in-one liquid coolers, I can assure you that this is a very capable little cooler.Features:Unlike its bigger brothers, the H55 isn't really meant for crazy overclocks. The unique feature of this cooler is that it operates very quietly (~1500RPM for the pump), yet manages to cool stock or mildly overclocked CPU effectively. The slim radiator should ensure that it fits most cases without issues and comes with all mounting kits nesescery to be used with both AMD and Intel CPUs.Noise:This unit is very quiet, HOWEVER, you must replace the stock fan since it is quite loud and cannot be controlled through the motherboard.The Pump makes a faint buzzing noise and that's about it. Provided you can replace the fan with something more quiet, this unit produces very little noise.Cooling Performance:For my system, the H55 keeps the Haswell i5 chip at 35-40c Idle and 45-60c load. This may seem high, but I have configured my system for quietness. I run my fans at 1,000 rpm, so the above is excellent performance for such a small unit.Cons:Only one set of screws are provided, therefore you require additional screws for push/pull. No vibration dampening mounts provided, and this can cause problems when the radiator is mounted on cheap cases.Overall, I recommend this unit. The H55 is a reliable, quite and effective cooler that's only slightly bigger than a 120mm fan.
Read more..

9.7.2019

First one of these that I got had clearly been used - there was no thermal paste on the pump. The second had an intermittent fault where one fan could not be speed controlled and always ran at full - noisy! I thought this was software related so put up with it trying to find a fix but became aware that moving the wires would temporarily resolve the issue - seems to be a loose connection or a broken wire but I couldn't track down the culprit so it was returned. The third seems to be working perfectly. I don't use the RGB - my fans are hidden behind the radiator in a NZXT H500, but the features are pretty comprehensive and it looks better than most of these if that's you're bag.Corsair iCue is pretty good - not perfect but at least as good as similar software from competitors. I do have static lights turned on on the pump and these look good - I have the logo text one colour and the ring a different colour and that looks fine. Cooling is great - I use on a 9900K OC to 5.0 GHz and it copes admirably at dissipating the enormous amount of heat that this chip produces. Even benchmarking the coolant never gets above 31C on quiet fan curve which is impressive. One tip, if fitting in an NZXT H500 ignore the internet wisdom which says that this case works best having all fans as exhaust - including AIO. I tried this and was underwhelmed. I have this fitted with fans pushing as intake and the overall results are much better.
Read more..

22.4.2020

Having used an NZXT AIO cooler in the passed which regrettably died after several years use, I was ready to replace it with another NZXT product. However with the recent upsurge in RGB products I was drawn away due to the absence of an RGB cooler in their product line. Having used other Corsair products with satisfying results I decided to buy this cooler. I'm so glad I did!My PC is substantially ovreclocked so I was expecting a similar level of fan noise as my previous AIO. However, I was shocked to discover that the corsair was almost silent and kept my CPU substantially cooler!The installation was a breeze though connecting all the necessary cables called for some careful thought in cable management.The lighting effects are also awesome!One thing to be aware of is that in common with other manufacuters, the illustrations are somewhat misleading. They all show the fans installed upside down! For most installtions and for efficiency, the fans need to pull air from outside, through the radiator into your case. All illustrations for these products show fans installed the other way round, i.e. sucking air from inside the case and blowing it through the radiator to the outside. Though this will work, it will not provide efficient cooling. Correct installation will not look as pretty as the manufacurers indicate (please see provided image).Despite these issues, this is a fantastic product.
Read more..

19.3.2019

I bought this to replace a Coolit ECO A.L.C. system in my old i7-2600K desktop PC. The Coolit pump developed a clicking noise before dying 8 years to the day from when I'd ordered it. It must have run for about 40,000 hours. I knew there was a problem when the CPU fan (the one cooling the radiator) started spinning at full speed and found the CPU was cooking at 85°C.The Corsair Hydro H60 would be a fairy easy fix on a new build (especially if you can get access to the underside of the motherboard) but it's a little more difficult when it's replacing an old cooling system.I had hoped that the H60 would be compatible with the old Coolit fixing frame on the back of the motherboard,as it would have saved me the work of removing the motherboard. No such luck! Whilst the stud threads were the same, they were a bit longer on the Coolit which meant the H60 couldn't be screwed down far enough to reach the CPU. So I had to remove the Coolit fixing frame (and the glue that attached it to the motherboard), as well as cleaning the old paste off the CPU.After reassembly I was quite relieved when the computer booted up. I did have to tweak the fan monitoring warning threshold in the ASUS BIOS, to reduce it to below 600 RPM.I obviously can't yet comment on the longevity of the H60 but it seems to be at least as quiet as the Coolit, and I think the CPU runs a bit cooler (it idles under 40°C).
Read more..

7.6.2018

I'd almost bought the EVGA CPU 240mm cooler, but I read some reviews which really threw caution in the mix. Instead I opted to get this one. The CPU cooler on my last PC was also Corsair, and had done very well for me.They're a brand I trust for sure. (You have to trust something when it's keeping £300+ CPU's safe.) CPU idles at around 30-33° it also seems to keep pretty cool under load, which is the most important thing.If I had a couple of negatives to add I'd say that I don't like the power cable, which is a USB-C type cable that plugs to the underside of the cooler. Maybe this is common with AIOC, but obviously us PC enthusiasts like cables to be as discreet as possible. This is not very discreet.The cooler is also very large, so make sure the case you are buying has enough space! (Can be front or top mounted.) For comparable scale, it's roughly the same length as my 1080ti (see images) and at least a third deeper. I have a Phanteks Enthoo Pro M Glass case and it fits with no issues whatsover, though I did't want the DVD drive, so removed the bays. If I did want a DVD drive I could see it being more problematic for some mid-tower cases.Aside from that, I'm very happy with my purchase and happy that I continued to believe in Corsair.
Read more..

10.2.2020

After years of just using a heat sync and fan I decided to try out one of these AIOs.I can say without a doubt, best experience I've had so far. My PC has never run so cool before. I recently upgraded to a Ryzen 7 2700x not overclocked yet, don't really need to.With the stock cooler it would run at 60 degrees on idle, and about 80 with games, but this thing keeps my PC at a wonderful 40 on idle and 60 with games.Not only that, it's so quiet I don't realise it's on. I have 1 fan on the rad because the position in the case makes it impossible to put both fans in. (Without breaking the mobo)I'm tempted to get another and mount it to my Graphics card, just for the fun of it.Even during intensive gaming,my case stays so cool.How my system is setup:Intake2x 120mm on the frontExhaust1x 120mm on the back1x 120mm on the rad pointing upI tried multiple setups, but this method has proven most efficient.Even if I could fix the 2nd rad fan on, I doubt it would make much more difference. The rad fan is fixed closest to the pipes, for more efficient cooling and has nothing to do with me not being able to put it on the other end...
Read more..

26.1.2019

This is the first liquid cooling system that I have installed in my desktop previously relying on a big lump of an air cooling fan. I have to say that installation is simplicity itself and a perfect fit on my 9th gen Intel CPU though the installation kit provided covers a range of Intel and AMD processors. CPU temperatures are much lower than previously achieved with an air fan and remain stable in use. There is an on-line video installation guide from Corsair which is helpful. However, one thing that does seem odd is that the 'radiator' cooling fan is set up to take external air and blow this through the radiator block into the case which does seem counter intuitive but this setup does work really well providing that you have enough extract from the case.Also, the radiator fan speed is controlled by Bios meaning quiet running speed but make sure to use the correct Bios fan speed controlled power pins on the main board. These is also subtle LED lighting on the CPU module that is nice.Overall, a great liquid cooling solution that looks good and works efficiently. A definite upgrade from an air cooled CPU fan.
Read more..

5.5.2019

Just wow, bought this after having a nightmare with my H100i V2, against my better judgement I went with another Corsair product - but this is absolutely phenomenal. Idling at 22 - 25 degrees, hitting max temps of 48 underload, this is with stock thermal paste as well! Struggled keeping the H100i below 50, though it is four years old now.Setup was a bit fiddly, was rather annoyed as I bought a seperate AM4 bracket for the H100I originally and threw away my generic AM4 bracket that came with the motherboard, this one however, uses the motherboard one, so I had to wait a couple of days to get a new AM4 bracket for my motherboard. Aside from that, the huge fans are nigh on silent on their highest setting and the pump makes a slight noise,as to be expected, but nothing major at all. I used to be able to turn on my old setup and use the white noise from the noisy fans to drown out the housemates, not with these - I suppose that's a good complaint to have!All this to say, if you've been burned by Corsair products in the past, like I have, give the H115i Platinum a go - you will not be disappointed!
Read more..

List All Products

Terms and ConditionsPrivacy Policy