logo

Info


Reviewbucket.co.uk scanned the internet for Thermal Grizzly Minus Pad 8 (TG-MP8-100-100-10-1R) reviews.
You can find all Thermal Grizzly Minus Pad 8 (TG-MP8-100-100-10-1R) reviews and ratings on this page.

Read the reviews.

Analysis


For Thermal Grizzly Minus Pad 8 (TG-MP8-100-100-10-1R), 89 customer reviews collected from 1 e-commerce sites, and the average score is 4.1.

Detailed seller stats;
Amazon has 89 customer reviews and the average score is 4.1. Go to this seller.

Detail


Click to list all products in this category.

Similar Items

7.4.2018

Really started loving these guys for cooling supplies. For thermal pad, it's super easy to work with and does help lower temps...just don't expect it to be earth shattering differences. It's a thermal PAD after allCons- Price for the average user (non-enthusiast)- Need some good fingernails to peel off the plastic film without risking tears or pulling some of it apart. Just take your time if biting your fingernails always ends up being more convenient than trimmers...Pros- THE enthusiast solution for pads, but may be overkill price wise for the average user. Much more expensive for a few degrees difference. Worth it for me by far though- About the best quality pad I've used.Not the slippery or super fragile ones that are cheap- The side with the thicker film really sticks well. Works great to get it on all of the memory chips and not worry about them falling off or moving, even if the heat sink needs to be slightly maneuvered after touching the less sticky side- Fantastic for VRM and memory chips. Temps lowered average 7 degrees on my Gigabyte Z270 motherboard while overclocking
Read more..

4.7.2019

I got this because I was in the process of upgradding my cpu so I decided to clean out my open loop and monoblock/gpu block out. I took apart my 1080 ti and noticed the thermal pads on the memory were off on some chips. It made me remember when i got the card new i was ablt to do a 400+mhz oc on the memory for a bit and i had to turn off the oc because it mad it unstable. Also the pads were cheap 0.5mm thermal pads. I replaed then with 1.5mm and mashed them down to cover the whole memory chip. I would have took pics if I knew how well it would work. Basically I increased the heat surface area to transfer to the vga block by using over cut and over thick cuts of thermal pads. I noticed right at boot.My card now car oc 400mhz on memory and my gpu core went down 5c under full load. I also used them on my mono block and south bridge on my mb and they were better then what was being replaced. These seem like they will last a long time. One of these was just enough to do all 11 memory chips on my 1080 ti with no room for error.
Read more..

19.1.2019

XBOX ONE X - opened the box, scraped all the trash off MY new property and added perfectly cut-to-size pads of this minus 8 "clay". Don't forget the chips off to the side. (No, I used TIM on the GPU... so there). I say "clay" because it really is kinda like a maleable clay. It is sticky on both sides, too. This material is sold as 2mm and when I scraped off the "old dried-paste" it measured just below 2mm thick. (Yes, I said it was "dried-paste"). So far so good. Put the box back together and I don't hear a fan.... EVER. Under heavy load, light load... the fan might be unplugged right? I get up close and listen and it's on but a few feet away it's silent.This stuff has the best "laboratory" specs vs all the competitors and with the TIM mod on the GPU to round it all out I FREAKING LOVE THIS STUFF. Too bad it's so prohibitively expensive. Do the mod. It works.
Read more..

25.1.2021

I had a nvme drive getting up to about 60+C with a different pad. Cooling the chassis didn't seem to help so the pad seemed to be more of a insulator than conductor.I swapped the old pad out with one of these and the difference is indeed well worth the purchase!If the chassis temp comes down so does the nvme temp!Temp was about 60C and now I'm seeing temps down in the mid 45CIn my situation I am using this pad to conduct heat from the nvme to a industrial grade embedded computer where the chassis is the heatsink and the fans are external and not attached to the chassis.If you're wondering if I recommend this product then yes, yes I do. It works.The packet comes with 1 pad that will need to be cut to length to fit your nvme or ssd.The width is just slightly wider than a nvme so only 1 cut is needed.
Read more..

11.5.2019

Hey here. Used this on a 1080 FTW2 in my system that I’ve had for a year and had quite trouble. I bought this and some NT-H2 to redo the thermal paste and now I’ve got leagues lower temperatures. Down by nearly 10 C in some cases but then again, the last time I opened my card I screwed up a few of the pads and I found that my last thermal paste application was the worst I’ve done so...A bit of a hassle since the FTW2 card has so many small and thing point for thermal pads but this should be completely worthwhile. Maybe help with value too when it comes time to flip the card. It’s good stuff and I had a little left over but couldn’t get the back of the VRMs on my card through the backplate,everything else is new pads but to be fair, that is one massive pad they put there.
Read more..

7.10.2018

I bought this to replace the stock thermal pads on my Gigabyte Z370N WIFI ITX motherboard. I cut a strip for the VRM heatsink as well as the M.2 SSD heatsink. The VRMs now take significantly longer to heat up and temps overall are reduced 5-20C depending on the CPU load. The 960 Evo SSD was throttling due to high temps (75C+) with the stock thermal pad but now stays much cooler (65C or less) and no longer throttles. This thermal pad is expensive but did exactly what I hoped for and is far better than the cheap pads Gigabyte uses on this particular motherboard. I wish I had swapped the pads out sooner!

22.5.2020

The best in its class. I have used this multiple times, the last use for this was on a playstation 4 pro. I used this to replace the junk factory ones along with the matching thermal paste and this made a huge a difference on the fan running full blast. Prior to the fan ran full speed was very noisy and didnt blow out much heat. After the install fan has never ran full speed and puts out alot more heat. This product is the best and will be the only one i ever use again. Did this prior to with cheap product and didnt change anything... this product did and is awesome.

12.5.2018

I bought this for my GPD Pocket since the case is aluminum. I lined the entire heatpipe with this thermal pad.The pad was a bit smaller than I expected, but that was my fault for not measuring out 30x30mm.With the pad applied, my GPD Pocket's fan (with Windows 10) went from always audible to actually turning off at idle and being much quieter overall.The pad conducts heat very well. There are now hotspots on the bottom of my GPD where the pad touches the shell, which I am happy with since that's heat that isn't forcing the CPU to throttle.

26.10.2020

Used these to replace the original pads between my GPU's VRM & heatsink. Didn't really need it for extra cooling & I had to double stack them because they were the wrong size, but the original pads fell apart when I removed them & these were what I had on hand at the time.It did reduce their temps quite a bit though! VRM temps went from around 90C when stress testing down to around 60-70C under the same conditions. So it's safe to say I'm very pleased with them all things considered. lol

6.9.2020

I have a PS4 pro that was about four months old and it already began to die on me and was really loud so I did a little research and found out that my thermal pads and paste needed to switched so I bought these pads and the paste they also sell then took apart my pro and removed the poor excuse for thermal paste and pads that were in the pro and it no longer runs like a jet engine ready to explode. Overall these work perfectly and would buy again if I ever build a PC

23.2.2021

This is some good stuff. Have a dell laptop that I upgraded the cpu from i5 to i7. The older i7 ran super hot and was shutting down. The gap between the cpu and heatsink was too much to use any paste. Installed this and my laptop runs much much cooler. Has not had a thermal shutdown since.Very pleased. This is my new goto cpu cooling product. Would definitely purchase again.

22.12.2020

So much better than the crappy crumbly ones I took off my PS4 PRO!!! I also added a pad to the HDMI chip because I had a extra piece left over. I cut out pieces slightly bigger than all the chips. Combined with Grizzly thermal paste my PRO is running great without the fan ramping up at all. I also cut a large hole right above the fan and added a housing with dust filter.

1.1.2020

Used some shady low-price no-name brand that offered to arrive in an hour and had ten thousand suspiciously positive reviews by bots (or people no smarter than bots). PS4 wouldn't boot.Used this one that I had to wait 2 days for but I know for sure it's good. PS4 boots.What I learned: Use what you know is good and don't let impatience get the best of you.

1.7.2019

Stuff is surely good but I couldn’t use it. It’s my mistake should have ordered the 1 mm one as I needed to use it in my Dell Inspiron 7573, on the cpu’s Second smaller die since dell heat sink has a hole and that is filled up with a silicon heat sink pad touching the heat pipe. It’s a bit of a odd design generally it’s not done so but anyways...

7.9.2020

My MSI video card showed really high memory temperatures when gaming and mining. Following some youtube videos, I replaced the thermal pads with this Thermal Grizzly stuff. Did a decent job lowering the temperatures for the memory.I do have some left, so the initial expensive cost will hopefully last me a few more applications.

List All Products

Terms and ConditionsPrivacy Policy