logo

Info


Reviewbucket.co.uk scanned the internet for Corsair ML140 Pro 140mm reviews.
You can find all Corsair ML140 Pro 140mm reviews and ratings on this page.

Read the reviews.

Analysis


For Corsair ML140 Pro 140mm, 268 customer reviews collected from 1 e-commerce sites, and the average score is 4.4.

Detailed seller stats;
Amazon has 268 customer reviews and the average score is 4.4. Go to this seller.

Detail


Click to list all products in this category.

Similar Items

29.7.2019

I was a bit skeptical... I made my new built a few months ago and was quite pleased with it: water CPU cooler radiator installed on the front of the case pushing air "in", the stock fans of the case on the back and top pushing air "out".The thing was that the fans of the water cooler (Corsair H115i) were much more efficient than the stock case fans on the back. The stock case fans were also "Cooler Master" fans (as the case is from Cooler Master), but without PWM speed control and possibly a much less air flow capacity.The result was that the 1080ti installed inside the case didn't have enough exhaust in my opinion. The GPU temperature was maintained at set-point 70degC,but with the GPU fans getting close to their maximum speed, which is wrong.The CPU cooler fans were not the cause, as the large surface of the radiator allows to exchange the energy required with large surface, low temperature, so even with the i7 9700K cranked up the air coming out of the cooler (inside the case) is just above 30degC.The problem was the 1080ti exhausting from the sides (the side glass gets really hot) and all that hot air not being exhausted efficiently from the case.I decided to install 2 of those PWM controlled fans. I tuned them from the mother board control software to maintain a set-point temperature inside the case, helping also the mother board chipset to stay cooler as well.The result is that while playing with the GPU fixed at 100% (as it should be when used on full potentials while gaming) the set-point of 70degC is now maintained with the GPU fans running between 40 and 50% speed, a MASSIVE improvement.Check always your case air flow and performance of each component. Don't install too many fans, just get the flow right and it will make a huge difference. Once you get to that, use decent fans as too many are useless if they are not great. And these fans are absolutely great!Last thing, they do get a bit noisy when cranked at high speed. But it is absolutely normal. The trick with these things is to tune the fan speed to have a good proportional response to temperatures so that they speed up only when required and stay nice and silent the rest of the time.
Read more..

28.7.2016

Having owned a built many high end rigs over the years, they all rely on one thing to keep them cool and running, fans. Much has been done over the years to eak out high performance, quiet performance etc and so I am glad to see someone come along and start innovating a bit more on what could be considered a mundane area that is absolutely critical to how well your rig is going to run. These days I favor quiet so I was keen to see this in action as it boasts a number of features above other fans.First impressions are superb. Well packaged in a good solid box and the fan itself is very well made.It uses a 4 pin PWM header and the cable is nice a long for a change making cable management a touch easier without resorting to extensions.The two key things here for me are the rubber dampers and magnetic bearing tech. I decided to try mine on my noctua cpu cooler and replaced the noctua fan. Initial impressions are that it shifts a great amount of air whilst remaining quiet. I have my fans tuned through my board to lower ranges and some turn off until they reach a certain temp. Ramping up they do get loud but no more so than my existing fan(s). The rubber dampers if case mounted would go a good way to reducing vibration transfer. These would be ideal fitted to a radiator in my opinion as they can focus some serious air flow. The manufacture of these fans is also rated for 200,000 hours of life which is very reassuring.The corners can be swapped out for coloured decals and there are LED versions. This is clearly corsairs way forward as a bit of research online shows these fans will be heading to corsair psu's and a corsair gfx card in conjunction with MSI.IN my opinion the fans justify their price and I am glad companies are innovating in this area. The fan is remianing on my cpu cooler in place of my trustee noctua for now!
Read more..

1.8.2016

Let’s start this review with almost a cliché, let’s compare the new ML120 pro to the original SP120 high performance editions.In this case let assume they are the ones fitted to the AIO 105h which is a few years old. I tested the original fans and found them to be way too loud and prone to further vibrations. I soon replaced them with the SP120 quiet additions which are not the best performers on the market, but they do look good.So the original SP120 HP spin at up to 2340rpm but the ones that are included with the 105h AIO water cooler are the basic model with grey fan blades and no rubber anti vibration ends.So how have things improved with the new ML120 Pro versions?1)At 1200rpm they are still pretty quiet - not something the SP120 HP or QE can achieve due to bearing rumble and at 1200rpm the QEs are nearly at the top end of their range. My ears say it is more than a gimmick.2) At 2400rpm, yes the new MLs are loudish but that is the noise of the air only, being forced through the radiator. With the SP120 HP edition you have that same noise plus bearing rumble plus vibration.3) The range of the ML120 pro is much better - spinning at a low 400 up to the 2400rpm limit.4) The design of the cage has been changed for a squarer, more efficient one, and the corners can be changed. Ever broken that rubber grommet in the SP120 HP or QE ones? I have and it is a pain.The downside to these improvements is the increased cost, the new ML120 pros do cost more but in this case it is justified.They are also recommended for PWM only because they need a constant 12v to maintain the magnetic levitating, so if you use a fan controller that uses a 3pin volt control method then it takes away the whole point of the maglev as you will have bearing rumble. Haven’t tested this as I have PWM fan control on my motherboard.
Read more..

19.7.2016

At present my computer is running a massively overclocked processor and graphics card, with four RAM slots filled. It generates a lot of ancillary heat within the case that needs to be moved out. My cooling current set-up has four input fans (all on the case) and three output (two CPU/GPU and one case). I've been using Zalman fans as they tended to be the quietest, with the little rubber doohickys instead of screws.I like corsair products, I have one of their water loops on my CPU, so how does this stack up against the Zalmans?The build quality is nice and chunky, if you like that type of thing. It's not going to fall apart on you anytime soon.Saying that you do need quite a bit of clearance to ensure it fits so probably not the best for smaller cases.The amount of air it pumps out is very respectable, you could easily use this as a case fan or secondary cooling fan on a self contained water unit. With a four prong connector it has the ability to be controlled from your motherboard or fan controller unit. Great if you want it quiet day to day but really need that oomph when you're working hard.As for sound, it is very quiet when on it's lowest setting, probably quieter than the Zalman's. I tried the screws to attach it, the rubber screw plates do make a bit of difference, but you'll really need to use rubber plugs to get the lowest vibration going back into the case. When it's going full blast it is LOUD, you really do hear the airflow (but not the fan itself).Yes it is a bit more expensive that other fans. Personally I'd say spend the few extra pounds and going for the units with built in LED's for that extra cool factor. Otherwise it's a sturdy unit with lots of air flow, no trouble recommending.
Read more..

25.1.2018

I know what you might be thinking... Magnetic Levitation fans?! Has to be a load of marketing rubbish... right? You are probably also considering these because you want them to do two main things: 1) Shift a load of air 2) be pretty quiet about doing it.Well, it probably is a little marketing rubbish, but there's no denying that whatever wizardry Corsair put in these fans, they are rather effective at doing what they do.Case fans now come in two flavours now-a-days... high air flow, meaning they are more efficient at shifting high volumes of air in open space and high static pressure, meaning they push air through things like radiators and filters better.I like my computer to be whisper quiet.It already was pretty quiet but the fans on my water cooler (Corsair SP120s) although high static pressure fans were a little noisier than I liked, even at lower RPMs. My intake/exhaust fans weren't really the right fans for the job either since they were high air flow Fractal R2s and I have filters on all the intakes and exhausts on the case (I don't like dust!).I connected up all the fans like for like and set them to run at the same RPM as used with the old fans. Not only is it now quite noticeably quieter (at idle/in Windows, I can actually hear the hard drives over the fans) but average temperatures are a good 5c lower too (I suspect mainly due to better air flow through the case).In all, it seems they are just as good as the non-Magnetic Levitation high static pressure fans, but they are quieter in doing so. There isn't a huge difference in price between the two either, if you aren't bothered about fancy LEDs in everything!
Read more..

27.3.2020

When I recently updated my PC with a new CPU, motherboard, RAM, etc., I decided to give it a bit of facelift by adding RGB components. It’s totally a cosmetic decision but if I’m going to have a big metal box in my room, then it might as well look the part.To complete the transformation, I needed some cooling fans that would light up as well. The watercooler already had two large RGB fans but I needed some for the case itself. Unfortunately, the motherboard (Asus Prime Z390-A) only has 12V RGB outputs and not the more common 5V ARGB outputs. So, I needed a set of fans that come with their own controller.I decided to go with this Corsair set (iCUE QL 120mm) as I was already using their iCUE software.The biggest stumbling block was the price! While I’ve always liked Corsair products, the asking price was very steep. In the end I decided it was worth it but I still feel they are too expensive.Fitting was easy. The RGB controller comes with a sticky back and can be placed in any convenient spot in your case. The fans are direct replacements for any 120mm fans. Each fan has two leads, one to go to your motherboard’s fan headers and the other goes into the RGB controller. There are an additional two leads to the controller. One is from any SATA power plug and the other goes to one of the motherboards USB2 header.Download the iCUE software from Corsair’s website and install it. You are then ready to light up your fans! I now have the iCUE software controlling my motherboard, RAM, water-cooler and case fans and it all works well together.Overall, a really effective RGB fan set but I wish it was a bit cheaper.
Read more..

27.6.2017

When these came out there were a lot cheaper than they are now, which has changed my review. These fans are good quality. Their main strength is the exceptional range of speeds they will run at. All the way from 400RPM to 2000RPM. They noticeably better than the standard Corsair fans and are both suitable as a case fan and a radiator or heatsink fan. They start to make noticeable mechanical noise at about 1300RPM so they are not as quiet as a Noctua or Noiseblocker, which are mechanically silent all the way up to their maximum RPM ( except for a woosh of air which all fans make at higher RPM's ). They are, however, cheaper, so they represent a good midpoint.When you need reasonable cost combined with low noise and very efficient air delivery, these are the fans for you.These of course are PWM fans ONLY so they are in the most expensive fan bracket, but they are also safer for critical cooling since PWM will always run at their minimum RPM even when commanded lower ( unless they are commanded to stop ). That's why it's not essential to get PWM for case fans but it is essential to get them for CPU/GPU cooler fans. Personally I use them as case fans too, since they just offer a much higher degree of control than a non-PWM fan.
Read more..

17.12.2016

There's no getting around it, these are very expensive fans. Kitting your rig with 4 of these to replace stock fans is a cool 100£.. good luck explaining that to your wife.But as long as you manage your expectations, then i think these could be worth it.1) Looks: I think they look great. PWM means they'll constantly be supplied with 12V so they'll keep their brightness even when you lower their rpm. Some led fans are 3 pins and would dim when you do so. The construction is also pretty sturdy.2) Cooling and noise: If you already had good quality fans (in the say 11£-15£ range), then you won't really notice decreases in temps. What they do have however is a pretty large rpm range,so you can lower them to inaudible levels, and crank them up all the way to 1800 rpm if you need to. That flexibility is pretty neat. Some fans would also rattle at low rpms, but these so far remain silent.Overall if you had crap and noisy fans then these would be a very worthwhile upgrade. If you already own good fans then it's a more difficult choice as these aren't cheap, and you'll have to decide whether the looks and build quality is worth it.
Read more..

2.8.2016

These new ML fans from Corsair are an impressive leap in quality and performance over their previous generation (AF and SP) fans.First, they are significantly heftier, a much denser, better build to them decreases rattle and gives a premium feel - especially on the blades, too. I picked the black bladed style with no LEDs and it looks exactly how I want it to - understated and practically invisible in a dimly lit case. Not everyone needs a light show to game.These fans feature a new magnetic levitation bearing as opposed to a traditional ball bearing design, the new 4-pin PWM socket pulls a constant 12v for the magnets while also allowing the fan to spin from a range of 400 to 1200 RPM.They have an incredible 5 year warranty, obviously corsair has confidence in their new fans.They are also not splitting the product stack - there are no SP or AF variants this time - only ML, the ML fans are capable at both static pressure and quiet air flow and boast significant performance increases with volume of air moved and pressure of the air moved - all while being whisper quiet, if that's what you want.
Read more..

3.10.2016

EditedI discovered the noise was a resonance from my corsair carbide case. I have placed a spacer between the fan and the grill and it's now a lot better with only the sound of air being pushed at 2000 rpm and under.+++++++++++++++++++Wow,I admit it, I was excited at the prospect of this fan and promise of silence it brought with it's MagLev no bearing contact.This was replacing a rather noisy Corsair AF Series 120. I hooked it up to my case expecting to hear the lovely whooshing of air hitting the side of my MOBO and GPU, what I was not expecting was the loud whining that's no different to a standard bearing fan with the adage that in my opinion it was louder than your average fan at half the price.Words are surely inadequate to convey to you how mediocre (being generous at that)this fan is.For £20 this is simply unacceptable.I fully intend to return this product and have made a promise to myself to be very, very wary of future Corsair products as this is not the first time their quality has been questionable at best.In my opinion you should avoid this fan, it's no quieter than most.
Read more..

23.4.2019

I ordered these to replace x2 Arctic cooling F12's that were doing a really good job whilst being quite quiet. They ran at 1500RPM max and whilst they were adequate I am running an R5 2600 @ 4.075Ghz which requires 1.368-1.380Volts.With the F12's I was hitting 65+ Degrees whilst gaming, not a massively hot CPU I reckon but still was hotter than I liked when doing anything more intensive.With the fan profile set to 100% at 62 Degrees and adjusted so the fan only ramps up from 70% @ 55 Degrees I get no hotter than 58 degrees whilst gaming and even running IBT @ max the CPU is 71 Degrees max with these Corsair ML120's.They do a great job and if you set your fan profile right they will not be incredibly noisy and will reduce your system temps.This is a good set of quality fans, they make little noise but the sound of rushing air, at higher temps they perform well and will range from 200rpm to 2500+ rpm(despite the packaging suggesting 2000rpm!)Im cooling my CPU with a 240 Radiator AIO and this has helped me worry less about pushing my PC to its max.
Read more..

3.8.2017

Like many of the other reviewers have already pointed out, these fans are not only denser and better built than previous generations of Corsair fans (SP and so on) but they're also significantly better at shifting air.Having bought five ML140s (two which replaced the one that came with the liquid cooler, 2 at the front and one on the back of the case) and two smaller ML120s (both of which are on the bottom of the case), there has been a notable improvement in general airflow throughout.Another difference with the other fans is that the LEDs (if you so choose to buy the LED versions) are built onto the actual hub as opposed to being built within the frame of the fan itself.If there is onenegative it would be that the threads of two of the fans I bought broke away when I screwed them in and while I was still able to secure them in place, it doesn't bode well for when I have to take them off again.Apart from that these are really great, and a definite step up from Corsair's previous generation of fans.
Read more..

14.8.2016

This is a well built fan, it's weighty and solid in construction. Mine came with grey rubber mounts (other colours are sold separately).In use it pushes out a good volume of air, at full speed it is a little noisy and this noise increases if the air has to pass though something like a fan grill. In my case all the fans are off until the temperature rises and at low speed this seems no more loud than the other fans I have but at full speed (something that never happens in my case) it did appear louder.It has a 4 pin PWM connector to allow the MB or a fan controller to keep it at its optimal noise V cooling range and this has a long 590mm cable which should be enough for most peoples uses.Overall a good fan,excellent build quality, but could be a little too loud if you can not control the speed by only attaching to a 3 pin fan header.
Read more..

28.7.2016

Corsair are known for their PC products so I have no doubt on the reliability of this fan. The biggest component killer on most PC's is dust. This fan can be controlled by the pins normally found all over a mother board marked FN1 FN2 etc etcConnect these up to the mother board and most mother bonds have a console where you can set the fan's speed or set it to vary depending on the temperature within the case. SAfest thing to do is buy at least 2 fans and set them up in the same way so you don't have a fan creating over pressure trying to push air into a case or a fan struggling to suck air out of a case. Have 2 and you'll have a very fast throughput without draining either fan ...Just remember to follow the direction around on the side of the fan mounting to know which was the air is going to flow.
Read more..

29.11.2016

These fans look amazing! They sound good!For the price I paid, £13.99 each, I would highly recommend these as they look and feel like a premium product. I would not pay full price for these as there are better options on the market. Installation was simple enough for me with my case, Corsair Spec Alpha, but one thing I'd recommend is before installing them into the case, use the provided screws to go through the installation points on the fans. The holes are a bit tight and a lot of pressure is needed so just screw each corner, take them out and then you can have a nice hassle free installation!If you're looking for some witchcraft near silent fans these are not the ones...because y'know...physics.If you're after a cool (pardon the pun) looking LED fan then these are the ones!
Read more..

List All Products

Terms and ConditionsPrivacy Policy